HOCL-12 90° Steel Strap Angle Clip – 12 Gauge by Doc's Industries Inc.

Anchoring wire supports or straps into tough metal decking can slow a job down fast when the wrong hardware is used. Under heavy loads, regular building vibration, or repeated movement above a ceiling grid, weaker clips can bend, slip, or snap. That can lead to sagging support runs, uneven overhead alignment, and inspection problems that cost your crew time.

Trying to improvise tie-off points on-site is not the answer either. It creates extra drilling, inconsistent spacing, and a messy finish that may not meet strict structural and safety requirements. The HOCL-12 90° Steel Strap Angle Clip gives your crew a cleaner and more dependable way to secure overhead support points from the start.

We stock the HOCL-12 as a heavy-duty 12-gauge seismic splay clip made for flush mounting against metal decks. This 90° steel strap angle clip includes multiple pre-drilled holes for screws and larger anchors, giving installers a rock-solid tie-off point right out of the box. Each bulk pack includes 100 pieces, weighs 17.10 lbs per box, and arrives ready for immediate jobsite deployment.

Setting Up Steady Support Tracks with the HOCL-12 90° Steel Strap Angle Clip

The HOCL-12 helps crews set strong, steady support paths where ceiling wire, utility lines, and overhead hardware need to stay secure. Instead of relying on light-duty clips that may twist over time, this 90° steel strap angle clip gives you a rigid 12-gauge steel connection point that holds its shape under regular strain.

For suspended ceiling work, the right clip helps keep wire runs aligned, steady, and easier to inspect. When layout crews are managing cable management, electrical support paths, or lightweight overhead service routes, the HOCL-12 gives them a clean attachment point that helps reduce movement and keeps the finished installation straight.

Hook and Hanger supplies this clip for contractors who need simple, reliable hardware that supports fast installation without creating extra field adjustments. It is especially useful when your team needs dependable seismic support around metal deck surfaces and must keep the work clean, consistent, and up to local building codes.

Smart Layout Configurations for Quick Ceiling Wire Tie-Offs

The HOCL-12 is laid out for practical jobsite use. Its small and large pre-punched openings give crews several ways to fasten the clip depending on the surface, load path, and approved fastener type. That flexibility makes it easier to move from deck fastening to wire tie-off without stopping to drill new holes by hand.

When crews are driving anchors into overhead concrete or metal deck surfaces, good overhead drilling and anchoring depend on hardware that lines up properly. This 90° steel strap angle clip helps speed up that process because the holes are already placed for common fastening methods.

The outer holes can support quick wire tie-offs, while the larger center opening can accept stronger anchoring hardware where the application calls for it. In tight overhead spaces, installers using extension poles can work more efficiently when each tie-off point is already prepared and easy to reach.

Dimensions and Product Specifications for the HOCL-12

Here are the key physical details that make the HOCL-12 a dependable choice for overhead support work:

• Thick Steel Core: Stamped from heavy 12-gauge structural steel to help prevent the clip from bending or losing its shape under continuous strain.

• Equal-Sized Legs: Formed with two balanced legs that each measure about 1.5" long, creating a sharp, rigid 90-degree angle.

• Wide Footprint Base: Measures roughly 2" wide to provide excellent surface contact against metal deck surfaces.

• Small Fastener Openings: Pre-punched with two smaller 1/4" holes that easily accommodate standard #8 or #10 self-tapping screws.

• Large Anchor Opening: Stamped with one large 5/8" hole designed to fit heavy-duty 5/8" expansion anchors or concrete screws comfortably.

• Protective Core Plating: Finished with eco-friendly, RoHS-compliant zinc plating for long-lasting rust protection in indoor building settings.

• Strict Code Compliance: Fully certified to meet California IR 25-2.13 safety and quality standards.

Common Ways to Use the HOCL-12 90° Steel Strap Angle Clip on the Job

The HOCL-12 is made for everyday interior support work where crews need a dependable 90-degree tie-off point. It is commonly used for seismic ceiling wire runs, overhead electrical tracks under corrugated metal decks, and structural support paths for lightweight utility hardware.

This 90° steel strap angle clip also works well when a project calls for consistent attachment points across a long ceiling run. Instead of changing hardware from one section to another, crews can keep the installation uniform and easier to inspect.

Hook and Hanger also supports contractors working with purlin clips, j-hooks, and eye lag screws when different ceiling or deck conditions call for different fastening methods. For heavier support requirements, crews can plan around beam clamps or threaded rod fasteners while keeping the HOCL-12 in place for dedicated seismic splay points.

The compact 2" width helps the HOCL-12 fit neatly into standard metal decking flutes. That makes it useful on commercial interiors where space is limited, ceiling alignment matters, and crews need each support point to sit flush without blocking other overhead parts.

Advantages of Using the HOCL-12 Support Clip

The HOCL-12 gives your crew several practical advantages on active jobsites:

• Heavy 12-gauge zinc-plated steel construction: Helps eliminate the risk of bracket tearing or sagging under load.

• Multi-hole stamping: Allows either outer hole to be used for tying off ceiling wire quickly and easily.

• Rigid 90-degree geometry: Acts as a certified splay clip for high-vibration areas needing extra seismic protection.

• Compact 2" width: Fits comfortably into standard metal decking flutes without taking up unnecessary space.

For contractors managing fast-paced installations, those small details matter. A dependable 90° steel strap angle clip can reduce layout delays, limit rework, and give inspectors a cleaner installation to review.

Get All Your Installation Supplies under One Roof with Hook and Hanger

Ordering the HOCL-12 with the rest of your project hardware helps keep purchasing simple. Instead of sourcing parts from multiple suppliers, your team can reduce paperwork, avoid shipping delays, and keep compatible jobsite supplies moving together.

Our hardware line includes angle clips, beam clamps, threaded rod fasteners, and other overhead support parts used across commercial interiors, ceiling systems, electrical pathways, and mechanical support layouts. Hook and Hanger focuses on supplying dependable parts that help crews work faster, stay organized, and maintain a cleaner finish from layout to final inspection.

This 90° steel strap angle clip is a smart choice when you need strong steel, clean hole alignment, and reliable seismic support in one small part. The HOCL-12 gives your crew a ready-to-use tie-off point that performs consistently across demanding overhead installations.

Get Your HOCL-12 90° Steel Strap Angle Clip Supply Directly From Hook and Hanger

Hook and Hanger supplies tough, reliable hardware built for real, everyday jobsites. Choosing the exact sizing and dependable seismic rating of this 90-degree strap clip gives your crew a fast, hassle-free installation backed by a supplier that understands the trade and focuses on helping your crew succeed.

To purchase your HOCL-12 inventory or to explore our complete selection of Angle Clips, Beam Clamps, and Threaded Rod Fasteners, visit hookandhanger.com today. For technical support, bulk pricing tiers, or submittal documentation, call our specialist team at 805-583-9920 or email info@hookandhanger.com.