ADOC1414TI Z Purlin Joist Clip with 14TI 1/4"-20 Rod Hanger

The ADOC1414TI purlin clip is an overhead support component for establishing a threaded attachment point on angled or sloped purlin and joist flanges. It combines a spring steel Z-style clip with a pre-assembled 14TI rod hanger, reducing the number of separate pieces an installer must carry and assemble at elevation. Hook and Hanger supplies this clip for contractors and purchasing teams planning cable management routes and suspended support work along structural steel.

Traditional overhead clips can turn a simple rod drop into a multi-step task. A worker may need to position a clip, align a separate hanger, add nuts, and secure the hardware while working from a lift or ladder. The ADOC1414TI purlin clip changes that sequence by providing an assembled clip-and-hanger arrangement with 1/4"-20 threaded impressions. Hook and Hanger stocks the component for crews that need a direct threaded connection without adding secondary nuts below the flange.

What Is the ADOC1414TI Z Purlin Joist Clip Assembly Used For?

The ADOC1414TI purlin clip grips the edge of an angled or sloped joist flange with spring force. Its Z-shaped profile is intended for flanges from 1/8 inch through 1/4 inch thick, providing a practical suspension point where drilling through steel is not the selected installation method. The attached 14TI rod hanger remains in position as the clip is placed, which helps crews establish repeatable threaded drops across a run of overhead framing.

After the clip is seated on the flange, the installer can spin a compatible 1/4"-20 threaded rod or attachment directly into the threaded impressions in the hanger. This layout supports the vertical drops used for suspended ceiling grid accessories, conduit support, low-voltage pathways, and related field assemblies. For projects that use several attachment styles, our wider selection of purlin clips and threaded rod fasteners helps purchasing teams match the overhead connection to the structural condition and supported system.

The ADOC1414TI purlin clip is particularly useful when the framing geometry makes conventional flat-bottom mounting hardware impractical. The spring steel clip engages the flange instead of depending on a drilled hole, while the 14TI hanger supplies the threaded receiving point below. Installation crews should confirm flange thickness, loading requirements, rod diameter, spacing, and the applicable project specifications before installing any overhead support component.

ADOC1414TI Z Purlin Joist Clip Assembly Specifications

• Spring steel Z-style clip: The ADOC1414TI purlin clip uses spring steel construction to grip the target flange with a compact overhead profile.

• Pre-assembled 14TI rod hanger: The rod hanger is already combined with the clip, limiting loose components during layout and installation.

• Flange thickness capacity: The clip is designed to engage angled or sloped joist flanges measuring from 1/8 inch to 1/4 inch thick.

• Threaded connection detail: Integrated 1/4"-20 threaded impressions accept compatible threaded attachments directly, eliminating the need for a separate nut at the hanger connection.

• Application focus: The assembly provides a threaded drop point for light-duty overhead support arrangements where the structural condition and approved loading criteria permit its use.

Compatible Installation Tooling and System Integration for the ADOC1414TI Purlin Clip

• Use the ADOC1414TI purlin clip with compatible 1/4"-20 threaded rod, hanger attachments, and approved support accessories sized for the planned overhead load.

• Pole tools can help crews position or attach related components from ground level, where the work sequence, clearance, and site safety plan permit. Review our extension poles when a reach-based installation method is appropriate.

• Some installations may need a separate structural connection method. Our beam clamps support other steel-framing conditions, while overhead drilling and anchoring equipment is used when an engineered drilled attachment is specified.

• Coordinate the clip with wire, tray, conduit, or ceiling support layouts before rod drops are placed. This reduces interference with other trades and helps maintain service access.

• For wood-framing transitions or non-steel attachment points elsewhere on the same project, eye lag screws may provide a separate compatible suspension approach when approved for that application.

Benefits of ADOC1414TI for Contractors and Ceiling Installation Crews

The ADOC1414TI purlin clip reduces high-elevation handling by combining the clip and rod hanger before it reaches the work area. Instead of managing several small pieces on a ladder or lift, the installer places one assembly on the flange and threads the required attachment into the 1/4"-20 impressions. This supports cleaner material staging and repeat installations within the clip’s specified flange range.

Its direct-threaded hanger connection also helps crews avoid the extra step of locking a nut onto a non-threaded mounting hole. The ADOC1414TI purlin clip can be incorporated into broader j-hooks layouts for pathway support or used beside angle clips where a project includes multiple overhead attachment conditions. Each support point should still be selected according to the framing type, load path, spacing plan, manufacturer instructions, and local code requirements.

Hook and Hanger supplies specialized overhead hardware for contractors working across new construction, tenant improvements, retrofit projects, and commercial facility installations. We stock this purlin clip alongside related suspension hardware, with shipping and bulk distribution support for material lists that must reach one site or multiple job locations. Our team can also assist purchasers in identifying complementary connection types when a drawing includes purlins, joists, beams, wood framing, or mixed support conditions.

Order the ADOC1414TI Z Purlin Joist Clip at Hook and Hanger

Choosing Hook and Hanger means equipping your construction crews with dependable, code-compliant overhead support parts designed to perform on demanding jobsites. By integrating the exact engineering, high-tensile spring steel structure, and pre-assembled threaded rod hanger compatibility of this specific clip into your project plans, you secure an efficient, hassle-free installation backed by a specialist team focused entirely on practical hardware solutions.

To purchase your ADOC1414TI Purlin Clip inventory or to explore our complete selection of alternative purlin clips, beam clamps, eye lag screws, and threaded rod fasteners, visit hookandhanger.com today. For technical support, bulk order quantities, or submittal documentation, call our specialist team at 805-583-9920 or email info@hookandhanger.com.